Vehicles
Sections
309 not categorized PORSCHE 944S GT WINGCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 968 1992-95 (includes uncategorized and accessory items) 944555271001DB This is the switch plate that holds the two power window switches on the drivers side and often breaks disallowing the fitment of the switches. an easy replacement by removing two screws. always sold in black. check the operation of the power window switches while you are at it. View/Change Diagram
$110.67
Make a selection DP4612R High efficiency performance and race brakes for track & street use, fast to bed-in, great for street vehicle brake upgrade. General Fitment911 1989-94944 1989-91 944 1985-88 968 1992-95 911 1974-77 911 1994-98
$223.06
Make a selection FVD111LAMVER Having problems with your check engine light? Want to run cat bypass pipes or a free flowing sports catalyst set up on your vehicle without having to reprogram the dme (ecu)? This adapter offsets the oxygen sensor about 1.5 inch from the gas stream. This achieves, in most cases, a sufficient measurement for the air/co ratio and increases the tolerance range between the pre and post cat oxygen sensors. In addition, the sensitivity of the oxygen sensor is also reduced allowing you to run a nearly any exhaust or catalytic set up, including bypass pipes, without the need to reprogram your ecu! Use only for the 2nd oxygen sensor (after catalytic)! General FitmentBOXSTER 1997-04911 GT3 2007-11 911 2005-08 911 GT3 2003-05 911 TURBO/GT2 2001-05 911 1998-05 911 1989-94 911 1987-89 911 1984-86 911 1978-83 CAYENNE 2007-10 CAYENNE 2003-06 CAYMAN 2006-08 BOXSTER 2005-08 968 1992-95 944 1982-85 944 1985-88 944 1989-91 928 1992-95 928 1987-91 928 1983-86 924 1986-88 924 1980-85 911 1994-98
$42.90
Make a selection CORB08 This single slider bracket is needed when installing any corbeau seat to your Porsche. This fits the following: General Fitment911 1989-94911 1994-98 944 1985-88 944 1989-91 968 1992-95
$139.00
Make a selection TL1407 Trying to adjust the inner rear caliper brake pad and cannot reach the adjuster through the swing arm? We have the solution! This super long 4 mm allen wrench with built in 3/8 inch drive socket accesses both the cap and adjuster and gives plenty of clearance for your ratchet. For 356, 911, 912, 914, 924, 928, 944, 968, and Boxster. General Fitment356 1960-65911 1965-69 928 1992-95 928 1987-91 928 1983-86 928 1978-82 912 1965-69 914 1970-76 924 1976-79 924 1980-85 924 1986-88 944 1989-91 944 1985-88 944 1982-85 968 1992-95 911 1989-94 911 1987-89 911 1984-86 911 1978-83 930 1975-77 911 1974-77 911 1970-73 911 1994-98 BOXSTER 1997-04 ALL
$28.00
Make a selection FVD50399101MM The moshammer front fender set blends just the right amount of motorsport pedigree with functionality. This aggressive design is captivating on any 991 model and offers a level of exclusivity not found with competitors body kits. The integrated fender vents lower the thermal load on the brakes by allowing the heat to be quickly ventilated up and out of the wheel arch. This composite fender set has been meticulously designed to bolt up to the factory locations for perfect panel fitment, alignment and consistent gaps. A perfect addition for a leased vehicle or for those looking to return the car to its original appearance in the future. These fenders complement the entire moshammer stormforce (991.1) / stormforce...(choose a part on the right to read more)
$3,631.10
Make a selection FVD3511M39040A2 The brembo gran turismo (gt) braking system with type iii rotors is ideal for ideal for clubsport and sprint type track events. It utilizes brembo type iii aggressive face-type discs that offer high initial response with a smooth pedal feel. The type iii offers the highest overall braking confidence and control, allowing a quick qualifying time or top results in sprint races. The GT line is dedicated to the most demanding customers. It originates from racing components, consisting of floating ventilated cross drilled discs, aluminum calipers with opposed pistons, a complete set of high-performance brake pads, abrasion and corrosion resistant goodridge braided steel brake lines and high-quality fastener hardware...(choose a part on the right to read more)
$5,054.50
Make a selection BES99102240SHD + 15 hp & + 14 torque - 200 cell high flow, tri metal German hjs "hd" high durability matrix sports catalysts. - can be used with FVD "brombacher" mufflers. - weighs 15.5 lbs. (7.0 kg). - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - made in Germany. - intoxicating growl at idle, partial throttle and wide open throttle. The catalytic converter cores used in this system are the most advanced in the industry. They are produced by hjs in Germany and are a 200 cpsi (cell per square inch) tri-metal design. Tri-metal cats are the freest flowing and environmentally friendly aftermarket cats produced today. Tri-metal catalytic converters are rodium, platinum and iridium coated and per...(choose a part on the right to read more)
$3,293.40
Make a selection FVD123019ATK Our k24 sport turbocharger is based off the optional k24 turbochargers, found in the GT2 or 993 turbo x50 models. They are remanufactured by borg warner certified technicians in Germany and are a cost-effective solution. The remanufacturing process includes full inspection of the turbocharger to ensure proper operation after the remanufacturing process. We then disassemble, clean and degrease the unit. The compressor wheels are exchanged, lightened and modified for more air flow. All clearances / shaft tolerances are checked for precision to ensure reliability. The end result is 20-30 additional horsepower, in the low and mid rpm range over the factory turbo. The sport turbo also has less lag than a factory k24...(choose a part on the right to read more)
$2,042.70
Make a selection FVD3511M39040AS The brembo gran turismo s (gt-s) braking system is ideal for clubsport and sprint type track events. The GT-s type iii system utilizes brembo type iii aggressive face type discs that offer high initial response with a smooth pedal feel. The type iii offers the highest overall braking confidence and control, allowing a quick qualifying time or top results in sprint races. Gt-s systems contain advanced calipers that include racing style radiators, dual inner piston seals, an inner pressure seal and an outer wiper seal. This innovative design provides the best combination of performance and long-lasting track use. The calipers are hard anodized in black (machined brembo logo in red) for resistance to corrosion and...(choose a part on the right to read more)
$5,164.50
Make a selection FVD116940 Anderungen der performance-kupplungsscheibe gegenuber der serien-kupplungsscheibe: der torsionsdampfer hat ein hoheres anschlagmoment: maximale belastbarkeit der torsionsdampfereinheit vor blockanschlag hoheres ubertragbares drehmoment anfahrverhalten ahnlich wie in serie bei fehlen der belagfeder ist das anfahrverhaltensportlicher, torsionsgefederte kupplungsscheiben dienen als schwingungsdampfer zwischen motor und getriebe.
$525.80
Make a selection FVD123020ATK Our k24 sport turbocharger is based off the optional k24 turbochargers, found in the GT2 or 993 turbo x50 models. They are remanufactured by borg warner certified technicians in Germany and are a cost-effective solution. The remanufacturing process includes full inspection of the turbocharger to ensure proper operation after the remanufacturing process. We then disassemble, clean and degrease the unit. The compressor wheels are exchanged, lightened and modified for more air flow. All clearances / shaft tolerances are checked for precision to ensure reliability. The end result is 20-30 additional horsepower, in the low and mid rpm range over the factory turbo. The sport turbo also has less lag than a factory k24...(choose a part on the right to read more)
$2,042.70
Make a selection FVD10699701 This radiator is produced by the racing & high-performance division of csf who design, engineer and manufacture the most advanced, efficient, and reliable cooling systems in the world. Csf manufacturers all aluminum high performance radiators that are a direct-fit replacement for Porsche racecars and streetcars. Csf radiators improve cooling efficiency by 10-20 % over the factory radiators. Each radiator is stamped to the same geometry and includes aluminum end tanks that offer more reliability than the factory plastic end tanks. Each csf end tank features quality welding and is generally considered the strongest tank design in the industry. If you are planning to upgrade or replace your radiators, we highly re...(choose a part on the right to read more)
$548.90
Make a selection FVD10699702 This radiator is produced by the racing & high-performance division of csf who design, engineer and manufacture the most advanced, efficient, and reliable cooling systems in the world. Csf manufacturers all aluminum high performance radiators that are a direct-fit replacement for Porsche racecars and streetcars. Csf radiators improve cooling efficiency by 10-20 % over the factory radiators. Each radiator is stamped to the same geometry and includes aluminum end tanks that offer more reliability than the factory plastic end tanks. Each csf end tank features quality welding and is generally considered the strongest tank design in the industry. If you are planning to upgrade or replace your radiators, we highly re...(choose a part on the right to read more)
$548.90
Make a selection FVD51299122MM The moshammer vented rear diffuser with fins is an aggressive design that reduces aerodynamic drag. This vented diffuser allows air that is trapped by the rear bumper to exit, allowing for greater top end performance. The design also incorporates 5 fins that improve laminar airflow by reducing turbulence. Moshammer manufactured this as a direct replacement, so it secures seamlessly to the factory locations with the original hardware. This is an ideal addition for a leased vehicle or for those looking to return the car to its original appearance in the future. When added to other elements of the evo rs (991.2 turbo/s) package, the result is a confident, cohesive stance with balanced downforce. Features: vented f...(choose a part on the right to read more)
$1,844.70
Make a selection BK147248 Born in the bohemian town of maffersdorf on september 3, 1875, ferdinand Porsche displayed unparalleled automotive engineering genius from his earliest years. Following stellar work at austro-daimler, as well as with his own engineering firm, he formed his own automobile company after world war ii, developing a line of sports cars which culminated in the fabled 911, the ultimate expression of Porsche’s original vision for the perfect sports car. General FitmentACCESSORY
$45.95
Make a selection BK250550 Follow the sweeping curves of the stunning new Porsche Boxster from its conception through design, testing, and development in this dynamic collection of lavish color photographs and archival images. Filled with clay models, show cars, prototypes, and production cars. Included are early design drawings and photographs of prototype models and testing. Includes see-through color diagrams. Softbound., 8"x 8 3/4", 128 pgs., 40 b&w ill., 80 color. General FitmentACCESSORY
$21.95
Make a selection BK1060 Recognized by Porsche enthusiasts, concours judges, even the Porsche factory as a definitive guide to Porsche authenticity. Get a detailed look at the year-to-year changes in body, chassis, trim, and interior components. Virtually every part is described and photographed allowing owner and restorer to determine originality. Brand new fourth edition. General FitmentACCESSORY
$59.95
Make a selection BK1061 This is a superb history of the 356 - from wartime tinkering with vws to the type 64 - through all years of 356 production. Excellent early photos, production shots, design studies, competition cars, exploded views, line drawings, specs, production figures, developmental history and much, much more. Hundreds of photos capture all the details through the years. General FitmentACCESSORY
$49.95
Make a selection 220512019 Adjustable wing pitch and accepts the 993 grill.
$3,534.30
Make a selection BBI9118170001 The bbi autosport race spec seat mounts are a direct bolt into the factory mount location for a hassle free, easy installation for your competition race seat. The bbi autosport seat mounts have a large range of adjustment options allowing fitment for all major fia and sfi approved seat brands and offers an integrated 5 and 6-point sub belt mounting location. The wide range of adjustment covers almost all possible seating preferences to properly seat drivers of all sizes. Cad designed, cnc laser cut and formed from one piece of .125” (1/8”) carbon steel with no welds to maximize strength and stiffness. All mounts are powder coated with a wrinkle black base and satin black sides.
$395.00
Make a selection 911606105JXATK The cis injection / k-jetronic warm up regulator is a critical component that performs the following functions: lowers pressure when engine is cold. Absorbs / distributes engine heat. Allows for an additional rich mixture under full load to prevent engine damage. Altitude correction. Send us your original part and we will have it remanufactured for you. We do not offer a core exchange on this part. Each part is remanufactured in Germany, so the lead times can vary. Sold individually. 1 necessary per car. Please note: this part number encompasses: Bosch part 0 438 140 045 for 911 SC models from 1977-80 and Bosch part 0 438 140 089 for 911 SC models from 1980-83
$744.70
Make a selection 911606105DXATK The warm up regulator is a critical component that performs the following functions: lowers pressure when engine is cold. Absorbs / distributes engine heat. Allows for an additional rich mixture under full load to prevent engine damage. Altitude correction. Send us your original part and we will have it remanufactured for you. We do not offer a core exchange on this part. Each part is remanufactured in Germany, so the lead times can vary between 6-8 weeks. Sold individually. 1 necessary per car.
$744.70
Make a selection 90134722303R The original rubber bushing is proven to be a weak link that can fail prematurely, allowing chassis geometry to be compromised. Symptoms include suspension movement during acceleration, braking and cornering. The powerflex black series bushing is manufactured of a more dense rubber than the original. It is a 95 shore compound that is more resistant to load than standard rubber which provides better control of chassis geometry for track use. Features: designed for track use improved track handling more precise and accurate alignment constant steering geometry increased tire life better steering feedback longer service life of suspension components less nvh (noise vibration hardness) than polyurethane bushings pl...(choose a part on the right to read more)
$37.40
Make a selection 22011099706 The 997 turbo ipd "y" pipe was built for the more demanding turbo performance customer. The factory y pipe becomes restrictive when adding substantial power gains. The ipd "y" pipe has larger inlets and an optimized diversion area allowing for even greater power gains. This superior and more efficient design flows 126 more cfm than the factory y pipe delivering the additional power needed to raise the performance bar on any turbo. The ipd "y" y pipe is designed to be a direct replacement of the factory OEM y pipe. There are no modifications or fabrication required for installing the ipd y pipe. This is an easy and straight forward r & r (remove and reinstall) bolt on upgrade. Note: contains everything nec...(choose a part on the right to read more)
$1,094.50
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |